Community AlphaAlpha MUADMINS
PLPolski
Zaloguj się
Na MuADMINSConfig ScannerWgraj zip swoich plików: rates, dropy, spoty, limityOtwórzNa MuADMINSSpotkajmy się na DiscordziePoproś o pomoc, pokaż, nad czym pracujesz, i rozmawiaj o MU z innymi właścicielami serwerów.Otwórz

MuADMINS

Rozwiązania

Krótkie poprawki częstych problemów z serwerem, klientem i stroną MU Online, każda ze źródłem i datą. “Potwierdzone” oznacza, że osoba, która pytała, potwierdziła, że poprawka zadziałała.

Rozwiązania: 80 dla “connectserver” · Wyczyść

  1. Konfiguracja serwera

    After about one hour of uptime nobody can log in: the login just keeps loading

    1. Set the server startup tool to reload (restart) the ConnectServer at an interval; the answer says this is done on all versions. 2. Restart the servers.

    ✓ Potwierdzone przez autora tematuDarksTeam · 2009-04-29
  2. Konfiguracja serwera

    All servers start fine, but in game after pressing Connect it says "You are disconnected from the server"

    The ConnectServer files still had a wrong IP. 1. Edit these files and put your local IP in each: D:\MuServer\CS\Connectserverlist, D:\MuServer\CS\Data\Connectserverlist, D:\MuServer\CS\Da...

    ✓ Potwierdzone przez autora tematuDarksTeam · 2009-05-24
  3. Konfiguracja serwera

    GameServer starts normally but crashes after a few minutes

    1. First read the GameServer logs: a broken event (Blood Castle, Devil Square) can stop the GS. 2. In this case the events and the GameServer were fine: the culprit was the ConnectServer....

    ✓ Potwierdzone przez autora tematuDarksTeam · 2011-05-11
  4. Konfiguracja serweraS2

    Client disconnects after choosing the server; the client log shows it connecting to someone else's IP (10.0.0.33, port 55901) with Pinkof Season 2 files

    The server files and the client still pointed to the IP of the person who packed them. 1. Put your own IP in the ConnectServer server list config. 2. Put your own IP in the JoinServer con...

    ✓ Potwierdzone przez autora tematuDarksTeam · 2015-02-13
  5. Konfiguracja serweraIGCNS9

    IGCN S9 E2 repack: 'No active Game Servers found' and disconnect when the server settings use a DDNS hostname

    1. Put the real (numeric) IP address in the GameServer and server list settings instead of the DDNS hostname. 2. Restart the ConnectServer and GameServer and connect again. 3. If you must...

    ✓ Potwierdzone przez autora tematuRaGEZONE · 2018-12-29
  6. Konfiguracja serweraMuEmu / Louis0.97k

    MuEmu 0.97k (kayito): how do I make a second server show up in its own box ("Server 2") on the server selection screen?

    1. The selection screen groups GameServers by ServerCode, 20 codes per box. 2. ServerCode 0 to 19 appear under Server 1, 20 to 39 under Server 2, 40 to 59 under Server 3, and so on. 3. Gi...

    ✓ Potwierdzone w zgłoszeniuGitHub (nicomuratona/MuEmu-0.97k-kayito) · 2024-12-04
  7. Konfiguracja serweraMuEmu / LouisS6

    MSVCP100.DLL is missing when starting ConnectServer, DataServer or JoinServer (MuEmu S6 files).

    Install the Microsoft Visual C++ 2010 Redistributable (x86, plus x64 on 64 bit Windows). Prefer the Microsoft download over single DLL sites.

    ✓ Potwierdzone przez autora tematuTuServerMU · 2018-06-11
  8. Konfiguracja serweraSeason 18 Episode 2

    Client disconnects right after choosing the server (server on a VPS)

    The server list shows, so the ConnectServer port is open, but the client is dropped when it moves on to the GameServer: the GameServer port is closed somewhere. 1. Find the GameServer por...

    ✓ Potwierdzone przez autora tematuTUServerMU · 2023-09-16
  9. NarzędziaIGCN

    IGC Dashboard: how to assign the dashboard license to a server license (Link URL) and when the servers must be restarted

    1. You need an unassigned dashboard license. 2. In the server license data form open the dropdown and click Assign Dashboard. 3. Fill Link URL with the web address where your dashboard is...

    Opracowanie źródła przez MuADMINSNot verifiedIGCN · 2024-10-30
  10. Klient gryOpenMUS6

    MuOnline Clone (MuMono): 'Data path not found', or the client cannot connect to the server

    1. The client needs the Season 20 (1.20.61) client data for its assets but speaks the Season 6 protocol. 2. *Data path not found*: set DataPath in Client.Main/Constants.cs to your Data fo...

    Opracowanie źródła przez MuADMINSNot verifiedGitHub (bernatvadell/muonline) · 2026-01-08
  11. Narzędzia

    Zyth3 Launcher: the server status check always shows the server offline

    1. In the launcher config put the server address as yourdomain.com or a plain IP like 123.101.12.102. 2. Do not write it as a web address like http://domain.com. 3. If your ConnectServer...

    Opracowanie źródła przez MuADMINSNot verifiedRaGEZONE · 2015-03-13
  12. NarzędziaMuEmu / LouisSeason 6 Episode 3

    MagicHand: which client files hold the server names, skill names and other texts of a MuEmu S6E3 client

    1. Open the client files with MagicHand. 2. Skill names: Data/Local/Eng/skill_eng.bmd. 3. Server names in the server list: Data/Local/ServerList.bmd. 4. Other game texts: Data/Local/Eng/t...

    ✓ Potwierdzone przez autora tematuTUServerMU · 2018-02-04
  13. Konfiguracja serweraclassic (MMT)

    New sub server (MMT files) gives a bind error and restarts.

    1. The sub server used the same port as the main one. 2. Give it its own port (for example 55903) and open it in the firewall. 3. Change its ServerCode in ServerList and MapServerInfo and...

    ✓ Potwierdzone przez autora tematuImperyus Games Brasil · 2009-10-30
  14. Klient grySeason 6

    Two separate servers (not subservers) both show in the client as server 1 with the same name

    The client serverlist file was broken, not the server codes. 1. Replace the client Data serverlist.bmd with a working one (for example from another client of the same version) and edit th...

    ✓ Potwierdzone przez autora tematuTUServerMU · 2021-06-18
  15. Konfiguracja serweraS2

    Season 2 files (KarLi tutorial): everything starts except GameServerCS, which fails

    1. Use your LAN address (192.168.x.x) only in MapServerInfo.dat and in the ConnectServer ServerList.dat. 2. Everywhere else in the server configs and the startup put 127.0.0.1. 3. In main...

    ✓ Potwierdzone przez autora tematuRaGEZONE · 2018-10-25
  16. Klient gryOpenMUany

    OpenMU: which connect server port should my client use, and why do I get disconnected right after choosing a server?

    1. Use port 44405 for the original client and 44406 for the open source client (sven-n/MuMain). 2. A disconnect right after server selection means the address reported by the IP resolver...

    Opracowanie źródła przez MuADMINSNot verifiedGitHub (MUnique/OpenMU docs) · 2026-08-23
  17. Konfiguracja serweraOpenMUany

    OpenMU local server without internet fails with "Could not start the server listeners: Name does not resolve (api.ipify.org:443)".

    1. The default Public IP resolver asks api.ipify.org for your public IP, which fails offline. 2. For local play, open the admin panel, game configuration, System. 3. Set the IP resolve se...

    ✓ Potwierdzone w zgłoszeniuGitHub (MUnique/OpenMU) · 2023-11-16
  18. Klient gryOpenMUany

    OpenMU: I start main.exe with the ClientLauncher pointing to 127.0.0.1:44405 and nothing happens, the server never sees a connection.

    1. The original client refuses 127.0.0.1. 2. Use another loopback address instead, usually 127.127.127.127, with port 44405. 3. Set it in the ClientLauncher (or in main.exe with a hex edi...

    ✓ Potwierdzone w zgłoszeniuGitHub (MUnique/OpenMU) · 2019-02-15
  19. Konfiguracja serweraMuEmu / LouisS8

    Two MuEmu S8 servers on one machine: the first works, the second disconnects at login although its ports (55902, 55920, 55961, 55971) are forwarded.

    1. Open the router page and check that the forwarding rules for the second server ports are really enabled, not only created. 2. If a rule turns itself off again after a refresh, delete i...

    ✓ Potwierdzone przez autora tematuTuServerMU · 2020-06-17
  20. Konfiguracja serweraOpenMUS6

    OpenMU in Docker on Windows: the client sees the server list but is disconnected when joining a server.

    1. Use the client version the server targets (1.04d English, Season 6 E3). 2. Open the ports in the Windows firewall (and allow NAT edge traversal). 3. The connect server hands out the IP...

    ✓ Potwierdzone w zgłoszeniuGitHub (MUnique/OpenMU) · 2019-11-12

MuADMINS Community Alpha: za darmo, tworzone przez społeczność, w aktywnym rozwoju.